Canon Pixma printer error - Carriage error or Error Code 5100

Canon Pixma printer error - Carriage error or Error Code 5100

Problems and Solutions:
Smearing or scratches on the carriage slit filmclean the timing slit film.Foreign material or paper debris that obstructs the carriage movement;
remove foreign material.Ink tank conditions;
Re-seat the ink tanks.

Read more

Reset Canon Pixma IP2770 | Absorber Full | Error Code 5B00

Reset Canon Pixma IP2770 | Absorber Full | Error Code 5B00

 

 

STEP 1:  Entering Service Mode

You have to enter in service mode in order to used the resetter. To do that follow this procedure,

1. Turn off the printer without pulling the power cords.

2. Hold down Resume button and press Power button.

3. Keep holding down Power button and let Resume button go.

4. Then Press Resume button 5 times then let BOTH buttons go.

5. You will notice that the Alternate Blinking error is gone, this means that the printer is in Service Mode state.

STEPS 2: Using the Resetter

1. After you download the resetter, extract it and double click "servicetool.exe"

2. Press the "Main" Button, Then press "EEPROM Clear" button if a pop-up appear just click OK

5. Then power off the printer(sometimes you have to press twice the power button to turn off) and turn on again. and its done!

 

Resetter Here

Read more

How to Reset Error Code E08 in Canon MP287 - Absorber Full

When the MP287 is turned on, it will immediately appear on the LCD panel error E08 MP287. And when we do print command, then the monitor screen will show “The Ink Absorber is Almost Full”. Caption MP287 E08 error on the screen as follows:

1. Turn on the Canon MP287, MP287 LCD then the panel will pop up error E08, and there is a description of “The Ink Absorber is Almost Full” on the screen of your monitor.
2. Download Resetter MP287 at this link http://www.mediafire.com/?esuhhe214i1dd6t
3. Canon MP287 printer must be in a state of SERVICE MODE. Do I read the next step.
4. Canon MP287 Turn off the E08 error by pressing the power. Do not unplug the power cord.
5. Press and Hold the button STOP / RESET followed by pressing the POWER button. So both buttons depressed position.
   
6. Release the button STOP / RESET but do not release the button POWER.
7. In these circumstances the POWER button is still depressed, press the STOP / RESET 6 times.
8. Then release both buttons simultaneously. Then the Canon MP287 will be in Service Mode condition.
9. LCD Panel MP287 will blank / dark and in your computer will detect new hardware. Ignore it.
10. The next step Exctract and Run Service Tool for MP287 MP287 E08 error you downloaded earlier.
11. Click the “PLAY”, then the printer will proceed, then MP258 will print one page with the words “D = 000.0″
12. Click “Clear EEPROM”.
13. Then click “EEPROM”, and the printer will print the results MP258 Resetter. Writing one line as follows: “TPage (COPY TTL = 00 000 = 00 000)”.
14. Canon MP287 Turn off by pressing the power.
15. Canon MP287 printer that error E08 will be normal again.

Read more

How to Reset Waste Ink Counter Canon Pixma iX5000 and iX4000 - Absorber Full

To reset Absorber Full for Canon PIXMA iX4000 or iX5000 you have to enter to service mode. Follow the step to enter to service mode on Canon PIXMA iX4000 or iX5000 :

1. Connect the Canon PIXMA iX5000 or iX4000 printer to the power cord. ( note : If the automatic power-on function is enabled in the printer, the printer enters the service mode for the first time, but it will never enter the service mode if the printer is turned off by the Power button. This is because the printer remains to be turned on internally if the power is turned off by the Power button. To prevent this, disconnection of the power cord is required before starting the printer in the service mode ) .
2. With the Canon PIXMA iX5000 or iX4000 printer powered off, while pressing the Resume/Cancel button, press and hold the Power button. (note : Don’t release the buttons. The Power LED lights in green to indicate that a function is selectable.)
3. While holding the Power button, release Resume/Cancel button. (Don’t release the Power button.)
4. While holding the Power button, press Resume/Cancel button 2 times, and then release both the Power and Resume/Cancel buttons.
5. When the Power LED lights in green, press the Resume/Cancel button 4 times to reset waste ink counter in the Canon Pixma iX5000 / iX4000. (note : If the Power LED does not light in green the printer does not enter the service mode, disconnect the power cord and plug it again. Then start from step 1 to start the printer in the service mode again).
6. At the end of the service mode, press the Power button. The paper lifting plate of the sheet feed unit will be raised.
   

Note :

• Each time the Resume/Cancel button is pressed, the Alarm and Power LEDs light alternately, Alarm in orange and Power in green, starting with Alarm LED.

Read more

How to reset waste ink Canon Pixma MP145 - Absorber Full

Solution:

• Connect the printer to a Power source.
• Turn off the printe.
• With the Printer power off, press the "Power" button while press and hold Stop/Reset button.
• When the Power led is light, press "Stop/Reset" button two times while pressing and holding the "Power" button.
• When releasing the "Power" button and the "Stop/Reset" button, the printer will move into a service mode
• When the on/off lights in green, press the "Stop/Reset" button four times to reset wase ink counter.
• Unplug cable power from a power source.

Read more

Printer Canon Pixma MP258 – Absorber Full

Printer Canon Pixma MP258 – Absorber Full

If your printer show P07 error it means that your ink absorber inside the printer is almost full. In order to solve this you need to clear or reset the counter protection of your printer. To do this, follow this steps.

First make sure that the power cable and usb cable are connected, before you perform the reset procedure. And download the resetter at the bottom of this post.

FIRST STEPS:  Entering Service Mode

You have to enter in service mode in order to used the resetter. To do that follow this procedure,

1. Turn off the printer without pulling the power cords.

2. Hold down STOP/RESET button and press Power button.

3. Keep holding down Power button and let STOP/RESET button go.

4. Then Press STOP/RESET button twice then let BOTH buttons go.

5. You will notice that the Alternate Blinking error is gone, this means that the printer is in Service Mode state.

SECOND STEPS: Using the Resetter

1. After you download the resetter, extract it and double click "servicetool.exe"

2. Load some papers in your printer and press the "Main" Button once, wait until the printing is done.

3. Then press "EEPROM Clear" button to clear EEPROM.

4. Then press EEPROM button and the printer will print some text.

5. Then power off the printer(sometimes you have to press twice the power button to turn off) and turn on again. and its done!

GFCH5V82RBB9 

Read more

Printer Canon Pixma MP258 – Error P08

First time, I found the problem Canon Pixma MP258 printer will not print from the cpu or the Copy Scan and P08 are the error messages on the printer panel. I could maybe try to reset, e turned out to be, then I created to copy directly, it was also error.

I've lost both cartridges, the ink was discharged, directly, I refill the black  and a color cartridge. Then I do a test print and the result is smooth and good wow.

If this error P08 does not clear, please 

Follow the instructions step by step

1. Turn off printer, cable power still plug in,
2. Press Stop/Reset button  don't release
3. Press Power Button don't release and than release Stop/Reset button
4. Press Stop/Reset button 2X and than release Power Button, wait until service mode to " 0 "
5. Turn off printer, cable power still plug in
6. Press Stop/Reset button  don't release
7. Press Power Button don't release and than release Stop/Reset button
8. Press Stop/Reset button 4X and than release Power Button, wait until service mode to " 1 "
9. Turn off printer, and loose cable power, wait one minute.
10. Connect cable power, turn on printer again, now this printer ready to use.

Read more